Search
Browse by Manufacturer
Browse Categories
Shopping Cart
Your cart is empty.




McAfee SECURE sites help keep you safe from identity theft, credit card fraud, spyware, spam, viruses and online scams



HS34 - Antenex 3/4" X-ACT Hole Saw

HS34 - Antenex 3/4
Your Price: $73.33
Item Number: HS34
Manufacturer: Laird
Manufacturer Part No: HS34
The Antenex X-ACT cuts a precise hole in the vehicle mounting surface to allow the installation of industry standard Antenex 3/4" NMO hole mounts

Cell phone antennas and amplifiers are frequency specific (more info).

A radio antenna installer's tool box just wouldn't be complete without the Antenex X-ACT. The X-ACT cuts a precise hole in the vehicle mounting surface to allow the installation of industry standard Antenex 3/4" permanent hole mounts. This innovative, one piece monolithic body design is machined from a single piece of hardened steel. It will not disassemble on the job!

The X-ACT features a replaceable self-centering pilot drill bit (HS34DB) that prevents dangerous "walking" of the saw and a replaceable hardened saw blade (HS34RB). The X-ACT also features a 1/8" depth limit that will prevent damage to the underlying headliner, yet it is deep enough to cut through thicker aluminum surfaces encountered on utility vehicles and ambulances. The X-ACT is designed for a 3/8" drill chuck and is nickel plated to guard the tool against corrosion. The X-ACT may also be used in other applications where a 3/4" hole is needed and depth is critical. Now in 3/8" also!

Features:

  • Bold new monolithic design machine from a single piece of tool steel.
  • Hole saw design limits the hole depth to 1/8" to prevent damage to the underlying headliner but will cut through the thicker. aluminum roof of some ambulances or utility vehicles.
  • Invaluable in other applications where depth is crucial.
  • Designed for 3/8" chuck or larger electrical drill.
  • Exclusive self centering drill bit restricts walking of saw.
  • Should scores paint for a better ground.
  • All components are hardened for a long life.

For Best Performance of the Saw:

  • Set the pilot drill bit about 1/8" beyond the tooth points - enough to establish and hold a center.
  • Be sure to chuck the hole saw properly on the flats.
  • Run the 3/4" hole saw at a maximum of 460RPM. Do not run the hole saw too fast - it will cut faster at a lower speed than at high speed.
  • Use a good grade of cutting oil to assure a cleaner cut and longer blade life. Operation without cutting oil will cause premature blade failure.
  • Apply sufficient feed pressure when teeth are in contact with work.
  • Hold the saw perpendicular to the surface of material being cut.
  • Do not try to saw holes at an angle to the work surface. When the teeth of the blade do not contact the work evenly, the hole saw will be twisted out of round and will break.
  • For replacement blades, order HS34RF
  • Remember - always wear safety glasses when using this tool!

Related Products

HS34DB - Antenex Replacement Drill Bit for HS34 3/4
HS34DB - Antenex Replacement Drill Bit for HS34 3/4" X-ACT Hole Saw
Your Price: $20.13
HS34DB - Antenex Replacement Drill Bit for HS34 3/4" X-ACT Hole Saw
Replacement Drill Bit for Antenex HS34 3/4" X-ACT Hole Saw
HS38 - Antenex 3/8
HS38 - Antenex 3/8" X-ACT Hole Saw
Your Price: No longer available
HS38 - Antenex 3/8" X-ACT Hole Saw
The Antenex X-ACT cuts a precise hole in the vehicle mounting surface to allow the installation of industry standard Antenex 3/8" NMO hole mounts
HS34RB - Antenex Replacement Blades for HS34 3/4
HS34RB - Antenex Replacement Blades for HS34 3/4" X-ACT Hole Saw
List Price: $94.29
Your Price: $54.95
You Save: $39.34 (42 %)
HS34RB - Antenex Replacement Blades for HS34 3/4" X-ACT Hole Saw
2 pack of replacement blades for Antenex HS34 3/4" X-ACT Hole Saw

HS34 - Antenex 3/4" X-ACT Hole Saw