|
Featuring cell phone antennas, cell phone amplifiers and cell phone repeaters from
Welcome to wpsantennas.com,
the largest Wilson Cellular Authorized Cell Phone Antenna and Cell Phone
Amplifier Dealer in the country. We are also a Digital Antenna Master Distributor
offering Digital Antenna Cell Phone Amplifiers and Repeaters, an ARC Wireless Solutions Distributor featuring the
Freedom antenna, an Antenex Distributor offering the full range of high quality Antenex antennas
and finally a Wireless Extenders (Wi-Ex) / zBoost Distributor. No matter what
your cellular signal issue is, we have a quality solution available for you. Feel free to
contact our Customer
Representatives and Engineering Staff to help design your solution!
We offer real solutions to your
cellular reception problems. Our systems range from simply attaching an
external
antenna directly to
your phone (with or without signal amplification) to multi-phone bi-directional
amplifier repeater (Nextel/iDEN, 800 MHz Cellular) systems that rebroadcast a
cellular carrier's signal throughout your building. We have solutions available
for your business, home, car, truck or RV and all cellular carriers.
We also offer a
large selection of Original
Equipment and Quality Aftermarket Accessories for a large variety of
cellular phones.
Whether you are looking for cell phone antennas, cell phone amplifiers or cell phone repeaters, we have the quality Wilson Cellular and Digital Antenna products that can help solve your cellular reception problem.
|
|
|
|
Wilson Cellular Complete Building Amplifier/Repeater System for iDEN (Nextel, SouthernLINC, Mike)
|
Wilson Cellular's new series of Smart Technology In-Building Cell Phone Amplifiers (cell phone repeaters) offer exceptional performance without causing harmful interference to the cell site.
|
Wilson Cellular Smart Technology Amplifier Features:
- Greater than 50dB (804005) or 60dB (804006) computer controlled adjustable AGC dynamic range
- Automatic Gain Adjusting in the event of oscillation or overload
- 2dB Gain Steps, 20-50dB (804005) or 30-60dB (804006)
- Automatic shutdown on overload
- Uplink squelch - optional
- TIA/EIA-98-E 3.5.1 Receiver Sensitivity better than -110dBm
- LED Indicators for Power, Oscillation and AGC
- 3 Watts Max Output Power
- +30dBm Linear Output Power
- +30dBm Max RF up/down
Installation Guide Addendum (PDF)
|
| This system is a complete kit compatible with iDEN systems (Nextel, Southern LINC, Mike) using the 806-866MHz band. Package
will contain all items required to build one full amplifier/repeater system. All
cables are crimped and all necessary adapters are included. The only additional
items you will typically require is the pole to mount the Yagi antenna on. |
|
Need custom cables?
We can custom build the cables to your required length using either
LMR-400 or lower loss LMR-600. Contact us at (877) 594-5766 for more
information. |
Note regarding 60dB
amplifier: If you intend to purchase the
60dB amplifier, please ensure that you have at least 70' of cable in your system
to allow for adequate antenna separation and do not use if you have 'full'
signal outside.
Nextel Rebanding note: Due to interference between the Nextel 800MHz band and the Public Safety 800MHz band, Nextel will be moving their service to the 900MHz band. What this means is that at some point your 800MHz repeater will need to be replaced with a 900MHz repeater. More (PDF).
We also offer a 900Mhz Nextel/SMR Add On Kit which can be used with an existing
compatible 900MHz amplifier/repeater system.
Package Contents:
Does not include pole/mast for mounting
Yagi - see
FMW4-YMST4: Antenex 4' x 1-1/4" Aluminum Mast and 4" Standoff Wall Mounts (2
Brackets)
Wilson Cellular Amplifiers extend cellular
services in poor coverage areas by amplifying both transmit and receive signals.
The amplifiers reduce problems with signal fades and dropped calls while
improving voice quality, service range and access. These multi-mode amplifiers
are designed to offer a cost-effective solution for use in buildings. Wilson
Cellular amplifiers are network compatible and enhance the cellular phone user's
satisfaction without comprising the operation of the cellular system.
This Amplifier-Repeater greatly improves signal
strength inside a building when using your cellular phone. It does this without
a physical connection to your phone, allowing you to walk freely during a call.
It even allows multiple phones to be used simultaneously.
The signal from the cellular tower is received
by the outside antenna and then amplifier and repeated to your phone through the
inside antenna. When the phone transmits it is received by the inside antenna
and then amplified/repeated through the outside antenna to the cellular tower.
- Wireless operation - no physical connection
to cellular phone
- In building and in vehicle models available
- Increases signal strength in buildings for
iDEN (Nextel, Southern LINC, Mike) frequencies (806-866MHz)
- Allows multiple phones to be used
simultaneously
- Increases your cellular phone's range
- Low cost solution for uncompromised
performance
- Also works for direct connect communication
|
50dB
(804005), 60dB (804006)
Amplifier/Repeater Coverage Area Comparison using:
|
Outside
Signal
(Test
Mode) |
Open Area
Coverage Distance
from Inside Antenna |
50
dB
804005 |
60dB
804006 |
Very Good
(-60dB)
Full Signal |
1200' (Driving 2 antennas)
May require attenuator |
Too Strong! |
Good (-75dB)
Full Signal |
300' or
200' (Driving 2 antennas) |
Too Strong! |
Marginal
(-90dB)
2-3 bars |
50' |
175' or
110' (Driving 2 antennas) |
Very Poor
(-100dB)
0-1 bars
(Not "No Service") |
15' |
50' |
Open area estimates: Walls will decrease coverage distance. Metal,
cement and cinderblock walls will severely attenuate or stop signal
penetration. Coverage area is
primarily determined by the strength of the outdoor signal and the
gain of the amplifier. To
determine correct amplifier size, see chart above and documents below. Antenna Separation:
In order for your system to
function properly, you must maintain adequate separation between the interior
and exterior antennas. The following rules will help you maintain adequate
separation:
-
Ensure that the
exterior Yagi antenna is aimed away from the interior dome
antenna.
-
Ensure that you
have 45' of separation between the interior and exterior
antennas when using the 50dB Amplifier and 75' of separation
between the antennas when using the 60dB amplifier. Of that, at
least 20' should be vertical separation (the Yagi should be
mounted at least 20' higher than the interior dome antenna.)
How dB Affects Coverage:
A 6dB increase in signal doubles the interior coverage distance while a 6dB
decrease will halve your interior coverage distance. Likewise, a 3dB increase
will increase the interior coverage distance by 43% and a 3dB decrease will
decrease it by 30%.
How you can increase the interior coverage distance/area (increase dB):
-
Use a larger amplifier:
The extra 10dB of the
804006 60dB Wilson
Cellular Amplifier (Cell Phone Repeater) for iDEN/Nextel will provide 3 times the interior
coverage distance of the
804005 Wilson Cellular Amplifier 50dB Amplifier (Cell Phone Repeater) for iDEN/Nextel (9x the
coverage area.) However, do not overpower your system (i.e: don't chose the
60dB amplifier when you have full signal outside.)
-
Improve the signal from the tower: Mount the
301111 Wilson Cellular
Yagi antenna higher or where there are less obstructions between it and
the tower.
-
Use less cable: Every 50' of Ultra Low Loss Cable loses 2dB of
signal. However, in order to maintain proper separation between the interior
and exterior antennas, you must maintain at least 40' to 45' of separation
between antennas when using the 50dB amplifier and 75' when using the 60dB
amplifier.
Additional Documentation:
Please note that while lightning protection will help guard against amplifier damage due to a lightning strike it does not guarantee it.
|
Price: $749.95
Buy Product Online | Visit Store Home
|
|
|
Manufactured by Wilson Cellular / Wilson Electronics |
|
|
|
Related Products
Wilson Cellular Complete Building Amplifier/Repeater System for 800Mhz Cellular - Configurable complete cellular amp (cell phone repeater) system for 800MHz Cellular. Not for Nextel/iDEN, PCS or 1700MHz AWS (T-Mobile US 3G)
50dB (801105), 55dB (CM800/55), 60dB (801106) and 65dB (CM800/65) amplifiers are all in stock.
FMW4-YMST4: Antenex (Laird Technologies) 4' x 1-1/4" Aluminum Mast and 4" Standoff Wall Mounts (2 Brackets) - Includes 4' mast and two standoff wall mount brackets. Idea for pole mounted Yagi and Fiberglass antennas
Wilson Cellular Complete Building Amplifier/Repeater System for 1900MHz Cellular (PCS) - Configurable complete cellular amp system for 1900MHz PCS. Not for Nextel/iDEN, 800MHz Cellular or 1700MHz AWS (T-Mobile US 3G)
Add On Interior Antenna Kit for Repeater Systems - Add on interior antenna kit allows you to add a second interior antenna to most repeater systems. Kit includes 2 pre-terminated cables, splitter, and interior antenna
|
|
|
|
Return To wpsantennas.com - Wilson Cellular, Digital Antenna, ARC Wireless, Wi-Ex & Antenex Cell Phone Antennas & Amplifiers: Cellular Amps, Cell Amplifier, Cell Phone Amplifier, Cell Phone Repeater, Cell Phone Antenna, Cell Phone Antennas, and Digital Antenna Cellular Antennas, Cell Signal Amplifiers, Repeaters and Boosters for Boat, RV, Car, Truck, Home and Office
|
|
|
|
Our products are also known as
cellular
antenna, cellular antennas, cell phone antenna,
cell phone antennas, cellular amp, cellular
amps, cell phone amp, cell phone amps, cellular
amplifier, cellular amplifiers, cell amplifier,
cell amplifiers, cell phone amplifier, cell
phone amplifiers, cell signal booster, and cell
signal boosters.
|
E-Mail |
Copyright 2001-2007
wpsantennas.com
7389 Airport View Dr SW Ste 200, Rochester, MN 55902 |
(877) 594-5766
M-F 8AM-5:30PM Central |
|
|
